Schneider Electric ALTIVAR 58 TRX Installationsanleitung Seite 104
- Seite / 126
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
© 1998–2003 Schneider Electric All Rights Reserved
Chapter 3—Diagnostics and Troubleshooting VVDED397047USR6/03
Fault Codes and Messages 06/2003
104
ERR 3
Serial link error due to incorrect value.
If the keypad display is remotely
mounted, electrical noise may be
present.
Cycle power on the drive controller. If the
keypad display is remotely mounted, verify
that the cable is properly shielded. Ensure
that the cable is routed away from motor
leads. If the problem persists, replace the
keypad display with part number
VW3A58101U. Reprogram any
parameters that are not at factory default
settings.
ERR 4
Internal error in the keypad display
software. If the keypad display is
remotely mounted, electrical noise may
be present.
ERR 5
Serial link error. If the keypad display is
remotely mounted, electrical noise may
be present.
ERR 6
Internal error in the keypad display
hardware
Cycle power on the drive controller. If the
problem persists, replace the keypad
display with part number VW3A58101U.
ERR 7
Serial link time out error. The keypad
display is not getting a response from
the drive controller. If the keypad
display is remotely mounted, electrical
noise may be present. The port baud
rate (tbr) may be set to 9600 bits/s.
Cycle power on the drive controller. If the
keypad display is remotely mounted, verify
that the cable is properly shielded. Ensure
that the cable is routed away from motor
leads. See page 58 for instructions for
resetting the tbr parameter back to 19200
bits/s. If the problem persists, replace the
control board on the drive controller with
part number VX4A581U. An Ini fault may
be displayed if the problem persists.
ERR 8
ERR 9
Internal error in the keypad display
software. If the keypad display is
remotely mounted, electrical noise may
be present.
Cycle power on the drive controller. If the
keypad display is remotely mounted, verify
that the cable is properly shielded. Ensure
that the cable is routed away from motor
leads. Re-program any parameters that
are not at factory default settings. If the
problem persists, replace the keypad
display with part number VW3A58101U.
ERR10
Serial link error due to incorrect length
of frame. If the keypad display is
remotely mounted, electrical noise may
be present.
Cycle power on the drive controller. If the
keypad display is remotely mounted, verify
that the cable is properly shielded. Ensure
that the cable is routed away from motor
leads. If the problem persists, replace the
keypad display with part number
VW3A58101U. Re-program any
parameters that are not at factory default
settings.
ILF
INTERNAL COMM. FAULT
Communication fault between the
control board and the option card.
Perform the Bus Voltage Measurement
procedure (Procedure 1 on page 98).
Check the connection between the option
card and the control board. If the drive
controller has a GPO card installed, see
instruction bulletin 30072-450-03 for
troubleshooting instructions.
InF
INTERNAL FAULT
• Internal fault.
• Internal connection fault.
Perform the Bus Voltage Measurement
procedure (Procedure 1 on page 98), then
check internal connections.
Table 27: Fault Codes and Messages (continued)
Fault/Message Probable Causes Corrective Actions
- Keypad Display VW3A58101 1
- TABLE OF CONTENTS 3
- Table of Contents 06/2003 4
- 06/2003 Table of Contents 5
- 06/2003 Introduction 7
- Keypad Display 11
- • Local command 11
- Keypad Display 06/2003 12
- Retaining Screw 12
- 06/2003 Keypad Display 13
- 50 Hz 60 Hz 14
- 50/60 Hz switch 14
- 06/2003 Access Levels 19
- Figure 6: Menus 20
- Access Levels 06/2003 22
- 06/2003 Language Menu 23
- Validate? ENT/ESC 25
- CUS:Customize 26
- Language 27
- Macro-Config 27
- 40 HP 200/240 V 27
- 1-DISPLAY MENU 27
- 1—Display Menu 28
- 2—Adjust Menu 29
- Handling Macro-Configuration 35
- Use Macro-Configuration 37
- Reassignment 39
- Reassignment (continued) 40
- 3—Drive Menu 41
- 3—Drive Menu 06/2003 42
- Set the CoS parameter to the 44
- T1 = 1/Acc 48
- T1 = 1/Dec 48
- 4—Control Menu 52
- ATV58 TRX terminal strip 53
- 24 V LI1 53
- LI1: Forward 53
- LIx: Reverse 53
- AOL AOH 20 55
- Parameter 55
- 5—I/O Menu 58
- 5—I/O Menu 06/2003 64
- 06/2003 5—I/O Menu 65
- LI1 LI2 LI3 LI4 +24 AIX 67
- —Drive menu 71
- • DC injection current 72
- • Brake release current 72
- • Nominal motor current 72
- Input Code Range Description 75
- • If AI3 = 10 V: limit = TLI 77
- T = non-adjustable delay 79
- • Brake release time (brt): 81
- • Brake engage time (bEt): 81
- 6—Fault Menu 85
- Table 21: 6—Fault Menu 86
- 7—Files Menu 89
- Table 22: 7—File Menu 90
- 06/2003 7—Files Menu 91
- Parameter Code Description 92
- Factory 92
- Password Fault 93
- 8—Communication Menu 94
- 8—Application Menu 94
- Red FAULT LED 95
- Maintenance 96
- Precautions 97
- Do not use 100
- Fault Codes and Messages 103
- ≥ 200 ms) 106
- Trip Point Reset Point 107
- VVDED397047USR6/03 Altivar 109
- Table 35: Menu 7—File Menu 112
- (continued 113
- (continued) 114
- Menu 6 – FAULT Menu (page 82) 115
- Menu 7 – FILES Menu (page 86) 115
- Catalog No. Description 117
- 91598106011107 126
Verwandte Produkte und Handbücher für Messen, Testen & Steuern Schneider Electric ALTIVAR 58 TRX
(8 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.072 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern