Schneider Electric Xantrex XW Installationsanleitung Seite 120
- Seite / 166
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Xantrex XW System Accessories Installation
5–6 975-0239-01-01
This manual for use by qualified personnel only
6. Place the unit into the mounting plate and secure it with four #6 screws.
7. Peel off the protective plastic coating covering the screen and indicator light.
To flush mount the Xantrex XW System Control Panel with no mounting plate:
1. Peel the backing from the supplied mounting template sticker and place it in
your chosen installation location. Use the template to mark the location for
the area to be cut out.
2. Pilot-drill the mounting holes (if necessary, depending on your mounting
surface) and, using a jigsaw, cut out the hole in which the Xantrex XW
System Control Panel will be inserted.
3. Route the network cable(s) from other Xantrex Xanbus-enabled devices
inside the wall and through the opening.
4. Connect the network cable(s) (and terminator if necessary) to either input on
the back of the Xantrex XW System Control Panel. See Figure 5-4.
Connect a network terminator to the Xantrex XW System Control Panel if it is
the last device at the end of a series-type network layout.
5. Place the unit in the opening and secure it with four #6 screws.
6. Peel off the protective plastic coating covering the screen and indicator light.
Figure 5-5 Securing the Xantrex XW System Control Panel
:
CAUTION: Equipment damage
Connect the Xantrex XW System Control Panel only to other Xantrex
Xanbus-enabled devices.
Although the cabling and connectors used in this network system are the same
as Ethernet connectors, this network is not an Ethernet system. Equipment
damage may result from attempting to connect these two different systems.
- Xantrex™ XW Power System 1
- Xantrex XW Power System 3
- Copyright and Contact 4
- About This Guide 5
- Conventions Used 6
- Related Information 6
- Important Safety Instructions 7
- Limitations on Use 8
- Single-phase Operation Only 8
- Explosive Gas Precautions 8
- FCC Information to the User 9
- Contents 11
- A Specifications 14
- B Wiring Diagrams 14
- 1 Introduction 21
- System Overview 22
- Xantrex XW Conduit Box 24
- 975-0239-01-01 1–5 25
- FGA Number: 28
- 865-1050 28
- 865-1060 29
- 2 Inverter/Charger 31
- Pre-Installation 32
- Clearance Requirements 34
- Mounting 34
- Inverter/Charger Installation 36
- 2–6 975-0239-01-01 36
- Step 2: Mounting the Inverter 37
- Step 4: Wiring the Inverter 39
- Inverter Grounding 44
- Grounding the DC System 45
- 975-0239-01-01 2–17 47
- Making DC Connections 48
- Making AC Connections 50
- CAUTION: 51
- Damage to the Inverter 51
- Grounding the AC System 53
- 2–26 975-0239-01-01 56
- 975-0239-01-01 2–27 57
- Distribution Panel 58
- AUX Port 60
- User Line Wiring 61
- AUX Port Terminal Assignments 61
- Confirm All Connections 62
- Enable the Inverter 63
- AC Voltage Check 64
- 2–36 975-0239-01-01 66
- Installation Steps 67
- Power Distribution Panel 68
- 975-0239-01-01 2–39 69
- 975-0239-01-01 2–41 71
- 2–42 975-0239-01-01 72
- See Figure 2-9 on page 2–14 76
- 975-0239-01-01 2–47 77
- 2–48 975-0239-01-01 78
- 2–52 975-0239-01-01 82
- 975-0239-01-01 2–53 83
- 3 Xantrex Xanbus 85
- The Xantrex Xanbus System 86
- Network Components 87
- Ordering Network Components 88
- Network Layout 89
- Installing the Network 90
- 4 Xantrex XW Solar 93
- PV Array Requirements 94
- Remove screws to access 97
- Removing Knockouts 98
- Mounting the Controller 99
- Secure with two more screws 100
- Place keyhole slot 100
- ¼" 6 mm 100
- Grounding 101
- WARNING: Shock Hazard 102
- WARNING: Fire Hazard 102
- Ungrounded Arrays 103
- Minimum Wire Gauge 105
- Over-current Protection 105
- Current Rating 105
- WARNING: Equipment damage 106
- Commissioning 111
- 5 Xantrex XW System 115
- Materials and Tools Required 117
- Choosing a Location 117
- WARNING: Explosion hazard 117
- WARNING: Shock hazard 118
- Rotate tabs to 119
- CAUTION: Equipment damage 120
- Verifying the Installation 122
- Preparing an Installation 123
- WARNING: Explosion Hazard 124
- CAUTION: Shock Hazard 126
- N/OFF/LED Indicator 128
- N/OFF/LED Indicator return 128
- Connecting the Generator 129
- CAUTION: Equipment Damage 131
- N/OFF switch. This light 132
- Verifying Power Is Available 135
- A Specifications 137
- Electrical Specifications 138
- Connection 139
- Specifications 140
- A–4 975-0239-01-01 140
- Ambient Temperature (°C) 141
- Xantrex XW Series Efficiency 142
- Charging Power Factor 143
- Mechanical Specifications 144
- Accessories 145
- B Wiring Diagrams 147
- 975-0239-01-01 B–3 149
- Xantrex Xanbus 150
- Network Terminator 150
- Xantrex XW Inverter/Charger 150
- Wiring Diagrams 152
- B–6 975-0239-01-01 152
- 975-0239-01-01 B–7 153
- B–8 975-0239-01-01 154
- C Alternate System 155
- 975-0239-01-01 C–3 157
- C–4 975-0239-01-01 158
- 975-0239-01-01 C–5 159
- CAUTION: Damage to Equipment 161
- Schneider Electric 166
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Schneider Electric Xantrex XW
(58 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.287 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern